How To Repair Patio Chair Straps
How to Re-Strap Patio Chairs
Vinyl strapping that has broken or become worn is easy to replace on patio furniture. Individual straps tin be replaced, or for a complete makeover, replace them all.
Refurbish your patio chairs by re-strapping.
Patio furniture takes a beating in the long, hot summers and over time volition first to prove signs of wear and tear. The UV rays from the sunday will crusade the vinyl strapping to go brittle and even discolor. Vinyl straps tin break, or poolside chairs can become stained with trunk oils and tanning lotions.
Fortunately, it'south relatively easy to replace cleaved or worn straps, or to give your vinyl patio chairs a facelift by replacing all the straps. With a niggling bit of your fourth dimension, a few materials and a petty patience, your furniture will have that new look again.
Vinyl patio chairs may apply a variety of methods of attaching the straps to the metallic frames, including rivets, pegs, or machine screws. Where possible, attempt to use the same method to adhere the new straps. On chairs where the straps are fastened with pegs, it'due south usually fairly simple to pry out the pegs and reuse them when attaching the new straps. Pop rivet tools are inexpensive and easy to use. Where you find it impossible to reuse the pegs or utilize rivets, yous can as well attach the new strapping with machine screws sized to lucifer the existing mounting holes in the chair frames.
- Vinyl strapping
- Pair of scissors
- Screwdriver
- Pliers
- Material measuring tape
- Bucket
- Piece of work gloves
- Tongs
- Towel
- Drill with 3/16-inch bit
- Pop rivet tool with rivets, or machine screws
-
Cutting off the sometime vinyl straps to be replaced, using scissors. Remove the straps by twisting and pulling them until the fasteners release from the frame of the chair. You can use a screwdriver and pliers to curve and pry out difficult-to-remove fasteners, such every bit expandable rivets.
-
Measure the length for the new strap, using a material measuring record. Position it at the pigsty in the chair frame, wrap information technology around the chair frame in the same direction every bit the vinyl straps, and pull it across to the opposite side of the chair. Wrap the tape effectually the frame and accept the measurement at the opposite hole. Reduce this measurement by ten percent to get the verbal length for the new strap. This reduction is necessary considering the new straps will be stretched when y'all install them.
-
Transfer the measurement to the new vinyl strapping and cut it to length. Drill a hole at each cease of the strap, about ane/2 inch from the end, using a drill and 3/16-inch bit. Cutting and trim the corners of the strap so they have dog-ear ends.
-
Boil h2o and pour the h2o into a bucket. Soak the new vinyl strap for about five minutes to soften it and prepare information technology for stretching. Carefully remove the strap with tongs, equally information technology will be quite hot. Wipe the strap dry with a clean towel.
-
Work quickly on the adjacent steps, as the vinyl strap needs to be warm and pliable plenty to stretch.
-
Insert a rivet, peg fastener, or machine screw into the holes at each end of the strap. Starting at one side of the chair frame, insert the fastener into the mounting hole in the frame. If using rivets, utilise the rivet tool to expand the rivet inside the mounting pigsty. If using auto screws, bulldoze in the screw until it fits securely in the frame. Peg-type fasteners can be driven with a mallet.
-
Holding the chair firmly in one hand, wrap the strap around the frame and across to the opposite side of the frame. Considerable force may be needed in order to stretch the strap. Insert the fastener into the opposite mounting hole and secure the strap in place.
Tip
Vinyl strapping tin also exist heated with a heat gun or hair dryer, merely be careful non to overheat it.
Tip
If yous have several straps to supercede, measure, cutting, and install them one at a time. This will ensure that each strap is warm enough to stretch.
The Drip Cap
- Patio furniture takes a chirapsia in the long, hot summers and over time volition starting time to show signs of vesture and tear.
- On chairs where the straps are fastened with pegs, information technology's commonly fairly simple to pry out the pegs and reuse them when attaching the new straps.
- Y'all can use a screwdriver and pliers to bend and pry out hard-to-remove fasteners, such as expandable rivets.
- Mensurate the length for the new strap, using a material measuring tape.
- Carefully remove the strap with tongs, as it will be quite hot.
- Considerable strength may be needed in lodge to stretch the strap.
- Insert the fastener into the reverse mounting hole and secure the strap in identify.
Source: https://homesteady.com/12283411/how-to-re-strap-patio-chairs
0 Response to "How To Repair Patio Chair Straps"
Post a Comment